Introduction
This document illustrates the configuration of IPSec between the PIX Easy VPN Remote hardware client feature and Easy VPN Server feature available in later releases of Cisco IOS® Software. The Easy VPN Remote feature for the PIX was introduced in PIX version 6.2 and is also referred to as hardware client/EzVPN client. When the Easy VPN Remote connects to a headend device, there are a minimum of five security associations (SAs), including one Internet Key Exchange (IKE) and four IPSec associations. When the Easy VPN Remote connects to the headend, it always negotiates two IPSec SAs with the IP address of the PIX's outside interface to any address behind the VPN server. This may be used for management purposes to connect to the PIX's outside interface from the network behind the Cisco IOS router (either via Secure Shell [SSH], Secure HTTP for PIX Device Manager [PDM], or Telnet). The SA is created by default without any configuration, and the other two SAs are created for the data traffic between the networks behind the PIX and the Cisco IOS router.
Refer to PIX-to-PIX 6.x: Easy VPN (NEM) Configuration Example for more information on a similar scenario where the PIX 506 6.x acts as the Easy VPN Server.
Refer to PIX/ASA 7.x Easy VPN with an ASA 5500 as the Server and PIX 506E as the Client (NEM) Configuration Example for more information on a similar scenario where the PIX/ASA 7.x acts as the Easy VPN Server.
Refer to PIX/ASA 7.x Easy VPN with an ASA 5500 as the Server and Cisco 871 as the Easy VPN Remote Configuration Example for more information on a similar scenario where the Cisco 871 Router acts as the Easy VPN Remote.
Refer to VPN Hardware Client on a PIX 501/506 Series Security Appliance with VPN 3000 Concentrator Configuration Example for more information on a similar scenario where the Cisco VPN 3000 Concentrator acts as the Easy VPN Server.
Prerequisites
Requirements
There are no specific requirements for this document.
Components Used
The information in this document is based on these software and hardware versions:
- PIX Firewall that runs software version 6.3(5)Note: The Easy VPN Client feature on the PIX was introduced in version 6.2.
- Cisco 7200 Series IOS Router that runs software version 12.4(4)T1Note: The Easy VPN Server feature was introduced in version 12.2(8)T).
The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.
Conventions
Refer to Cisco Technical Tips Conventions for more information on document conventions.
Configure
In this section, you are presented with the information to configure the features described in this document.
Note: Use the Command Lookup Tool ( registered customers only) to find more information on the commands used in this document.
Network Diagram
This document uses this network setup:
Configurations
This document uses these configurations:
Cisco IOS Router
ezvpn_server#show running-config
Building configuration...
Current configuration : 1894 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname ezvpn_server
!
boot-start-marker
boot system disk1:c7200-adventerprisek9-mz.124-4.T1.bin
boot-end-marker
!
!
!--- Enable the authentication, authorization, and accounting (AAA)
!--- access control model.
aaa new-model
!
!
!--- Enable X-Auth for user authentication.
aaa authentication login userauthen local
!--- Enable group authorization.
aaa authorization network groupauthor local
!
aaa session-id common
!
resource policy
!
ip subnet-zero
ip cef
!
!--- For local authentication of the IPSec user,
!--- create the user with password.
username remoteuser1 password 0 remotepass
username cisco password 0 cisco
!
!
!
!--- Create an Internet Security Association and Key Management Protocol
!--- (ISAKMP) policy for Phase 1 negotiations for the hardware client.
crypto isakmp policy 10
hash md5
authentication pre-share group 2
!
!--- Create a group that will be used to specify the
!--- Windows Internet Name Service (WINS) and Domain Name System (DNS)
!--- servers' addresses to the hardware client for authentication.
crypto isakmp client configuration group hwclient
key test123
dns 172.22.1.101
wins 172.22.1.102
domain cisco.com
pool ippool
!
!
!--- Create the Phase 2 Policy for actual data encryption.
crypto ipsec transform-set myset esp-des esp-md5-hmac
!
!--- Create a dynamic map and apply the transform set that was created above.
crypto dynamic-map dynmap 10
set transform-set myset
!
!
!--- Create the actual crypto map, and apply
!--- the aaa lists that were created earlier.
crypto map clientmap client authentication list userauthen
crypto map clientmap isakmp authorization list groupauthor
crypto map clientmap client configuration address respond
crypto map clientmap 10 ipsec-isakmp dynamic dynmap
!
interface FastEthernet0/0
ip address 10.10.10.2 255.255.255.0
duplex half
!--- Apply the crypto map on the outside interface.
crypto map clientmap
!
interface ATM2/0
no ip address
shutdown
no atm ilmi-keepalive
!
interface FastEthernet4/0
no ip address
shutdown
duplex half
!
interface Ethernet5/0
ip address 172.22.1.1 255.255.255.0
duplex half
!
interface Ethernet5/1
no ip address
shutdown
duplex half
!
interface Ethernet5/2
no ip address
shutdown
duplex half
!
interface Ethernet5/3
no ip address
shutdown
duplex half
!
!--- Create a pool of addresses to be assigned to the VPN Clients.
ip local pool ippool 172.22.1.50 172.22.1.70
ip classless
no ip http server
no ip http secure-server
!
!
!
logging alarm informational
!
control-plane
!
gatekeeper
shutdown
!
!
line con 0
stopbits 1
line aux 0
stopbits 1
line vty 0 4
!
!
end
ezvpn_server#
PIX
pix506#show running-config
: Saved
:
PIX Version 6.3(5)
!--- Specify speed and duplex settings.
interface ethernet0 auto interface ethernet1 auto
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password WwXYvtKrnjXqGbu1 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
hostname pix506
domain-name cisco.com
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names
pager lines 24
mtu outside 1500
mtu inside 1500
!--- Define IP addresses for the PIX's inside and outside interfaces.
ip address outside 10.10.10.1 255.255.255.0
ip address inside 172.16.1.1 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
pdm history enable
arp timeout 14400
!--- Define the outside router as the default gateway.
!--- Typically this is the IP address of your ISP's router.
route outside 0.0.0.0 0.0.0.0 10.10.10.2 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout sip-disconnect 0:02:00 sip-invite 0:03:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server TACACS+ max-failed-attempts 3
aaa-server TACACS+ deadtime 10
aaa-server RADIUS protocol radius
aaa-server RADIUS max-failed-attempts 3
aaa-server RADIUS deadtime 10
aaa-server LOCAL protocol local
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
telnet timeout 5
ssh timeout 5
console timeout 0
!--- Define the VPN peer IP address.
vpnclient server 10.10.10.2
!--- Specify whether Client/PAT (Port Address Translation) mode
!--- is to be used or whether Network Extension Mode (NEM) is to be used.
vpnclient mode network-extension-mode
!--- Define Easy VPN Remote parameters.
!--- This is the pre-shared key used in IKE negotiation.
vpnclient vpngroup hwclient password ********
!--- This is the extended authentication username and password.
vpnclient username cisco password ********
!---This enables vpnclient on the PIX.
vpnclient enable
terminal width 80
Cryptochecksum:fdbd365f0b4cdc6707a50efeeeb8ed44
: end
Verify
PIX show Commands and Sample Output
Use this section to confirm that your configuration works properly.
The Output Interpreter Tool ( registered customers only) (OIT) supports certain show commands. Use the OIT to view an analysis of show command output.
- vpnclient enable command—Enables an Easy VPN Remote connection. In NEM, the tunnel is up even when there is no interesting traffic to be exchanged with the headend Easy VPN Server.
pix506(config)#vpnclient enable
- show crypto isakmp policy—Displays the parameters for each IKE policy.
pix506(config)#show crypto isakmp policy
Default protection suite
encryption algorithm: DES - Data Encryption Standard (56 bit keys).
hash algorithm: Secure Hash Standard
authentication method: Rivest-Shamir-Adleman Signature
Diffie-Hellman group: #1 (768 bit)
lifetime: 86400 seconds, no volume limit
This example shows output from the show crypto isakmp policy command after the hardware client is enabled.
pix506(config)#show crypto isakmp policy
Protection suite of priority 65001
encryption algorithm: DES - Data Encryption Standard (56 bit keys).
hash algorithm: Message Digest 5
authentication method: Pre-Shared Key with XAUTH
Diffie-Hellman group: #2 (1024 bit)
lifetime: 86400 seconds, no volume limit
Protection suite of priority 65002
encryption algorithm: DES - Data Encryption Standard (56 bit keys).
hash algorithm: Message Digest 5
authentication method: Pre-Shared Key
Diffie-Hellman group: #2 (1024 bit)
lifetime: 86400 seconds, no volume limit
- show crypto ipsec transform—Displays the current IPSec transforms.
pix506(config)#show crypto ipsec transform
This example shows output from the show crypto ipsec transform command after the hardware client is enabled. Before the vpnclient enable command is used, there was only one default protection suite for ISAKMP. After the command is issued, Easy VPN Remote automatically builds four proposals in addition to the default protection suite. In addition, there is no IPSec transform set before the enable command is used. The transform set is built dynamically after the command is issued.
pix506(config)#show crypto ipsec transform-set
Transform set _vpnc_tset_9: { esp-des esp-md5-hmac }
will negotiate = { Tunnel, },
Transform set _vpnc_tset_10: { esp-null esp-md5-hmac }
will negotiate = { Tunnel, },
Transform set _vpnc_tset_11: { esp-null esp-sha-hmac }
will negotiate = { Tunnel, },
- show crypto isakmp sa—Displays all current IKE SAs at a peer.
pix506(config)#show crypto isakmp sa
Total : 1
Embryonic : 0
dst src state pending created
10.10.10.2 10.10.10.1 QM_IDLE 0 2
- show vpnclient—Displays VPN Client or Easy VPN Remote device configuration information.
pix506(config)#show vpnclient
LOCAL CONFIGURATION
vpnclient server 10.10.10.2
vpnclient mode network-extension-mode
vpnclient vpngroup hwclient password ********
vpnclient username cisco password ********
vpnclient enable
DOWNLOADED DYNAMIC POLICY
Current Server : 10.10.10.2
Primary DNS : 172.22.1.101
Primary WINS : 172.22.1.102
Default Domain : cisco.com
PFS Enabled : No
Secure Unit Authentication Enabled : No
User Authentication Enabled : No
Backup Servers : Deleted by order of the headend
- show crypto ipsec sa—Displays IPSec SAs built between peers.
pix506(config)#show crypto ipsec sa
interface: outside
Crypto map tag: _vpnc_cm, local addr. 10.10.10.1
local ident (addr/mask/prot/port): (10.10.10.1/255.255.255.255/0/0)
remote ident (addr/mask/prot/port): (0.0.0.0/0.0.0.0/0/0)
current_peer: 10.10.10.2:500
PERMIT, flags={origin_is_acl,}
#pkts encaps: 3, #pkts encrypt: 3, #pkts digest 3
#pkts decaps: 3, #pkts decrypt: 3, #pkts verify 3
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 0, #pkts compr. failed: 0,
#pkts decompress failed: 0
#send errors 0, #recv errors 0
!--- As shown here, ping packets were successfully exchanged
!--- between the Easy VPN Remote (PIX) and the Easy VPN Server (IOS).
local crypto endpt.: 10.10.10.1, remote crypto endpt.: 10.10.10.2
path mtu 1500, ipsec overhead 56, media mtu 1500
current outbound spi: 533f74a9
inbound esp sas:
spi: 0xad0984cc(2903082188)
transform: esp-des esp-md5-hmac ,
in use settings ={Tunnel, }
slot: 0, conn id: 4, crypto map: _vpnc_cm
sa timing: remaining key lifetime (k/sec): (4607999/3001)
IV size: 8 bytes
replay detection support: Y
inbound ah sas:
inbound pcp sas:
outbound esp sas:
spi: 0x533f74a9(1396667561)
transform: esp-des esp-md5-hmac ,
in use settings ={Tunnel, }
slot: 0, conn id: 3, crypto map: _vpnc_cm
sa timing: remaining key lifetime (k/sec): (4607999/3001)
IV size: 8 bytes
replay detection support: Y
outbound ah sas:
outbound pcp sas:
local ident (addr/mask/prot/port): (172.16.1.0/255.255.255.0/0/0)
remote ident (addr/mask/prot/port): (0.0.0.0/0.0.0.0/0/0)
current_peer: 10.10.10.2:500
PERMIT, flags={origin_is_acl,}
#pkts encaps: 5, #pkts encrypt: 5, #pkts digest 5
#pkts decaps: 5, #pkts decrypt: 5, #pkts verify 5
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 0, #pkts compr. failed: 0,
#pkts decompress failed: 0
#send errors 0, #recv errors 0
!--- As shown here, ping packets were successfully exchanged
!--- between hosts behind the Easy VPN Remote (PIX) and the Easy
!--- VPN Server (IOS).
local crypto endpt.: 10.10.10.1, remote crypto endpt.: 10.10.10.2
path mtu 1500, ipsec overhead 56, media mtu 1500
current outbound spi: 2eca448b
inbound esp sas:
spi: 0xc82c0695(3358328469)
transform: esp-des esp-md5-hmac ,
in use settings ={Tunnel, }
slot: 0, conn id: 2, crypto map: _vpnc_cm
sa timing: remaining key lifetime (k/sec): (4607999/2997)
IV size: 8 bytes
replay detection support: Y
inbound ah sas:
inbound pcp sas:
outbound esp sas:
spi: 0x2eca448b(785007755)
transform: esp-des esp-md5-hmac ,
in use settings ={Tunnel, }
slot: 0, conn id: 1, crypto map: _vpnc_cm
sa timing: remaining key lifetime (k/sec): (4607999/2988)
IV size: 8 bytes
replay detection support: Y
outbound ah sas:
outbound pcp sas:
- show access-list—Displays the contents of access lists.
access-list cached ACL log flows: total 0, denied 0 (deny-flow-max 1024)
alert-interval 300
access-list _vpnc_acl; 2 elements
access-list _vpnc_acl line 1 permit ip 172.16.1.0 255.255.255.0
any (hitcnt=18)
access-list _vpnc_acl line 2 permit ip host 10.10.10.1
any (hitcnt=6)
!--- The above output shows the dynamically built access lists to identify
!--- interesting traffic for encryption.
IOS show Commands and Sample Output
- show crypto isakmp sa—Displays all current IKE SAs at a peer.
ezvpn_server#show crypto isakmp sa
IPv4 Crypto ISAKMP SA
dst src state conn-id slot status
10.10.10.2 10.10.10.1 QM_IDLE 1026 0 ACTIVE
- show crypto ipsec sa—Displays IPSec SAs built between peers.
ezvpn_server#show crypto ipsec sa
!--- As shown above, ping packets were successfully exchanged
!--- between the Easy VPN Remote (PIX) and the Easy VPN Server (IOS)
!--- as well as hosts behind them.
interface: FastEthernet0/0
Crypto map tag: clientmap, local addr 10.10.10.2
protected vrf: (none)
local ident (addr/mask/prot/port): (0.0.0.0/0.0.0.0/0/0)
remote ident (addr/mask/prot/port): (10.10.10.1/255.255.255.255/0/0)
current_peer 10.10.10.1 port 500
PERMIT, flags={}
#pkts encaps: 3, #pkts encrypt: 3, #pkts digest: 3
#pkts decaps: 3, #pkts decrypt: 3, #pkts verify: 3
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 0, #pkts compr. failed: 0
#pkts not decompressed: 0, #pkts decompress failed: 0
#send errors 0, #recv errors 0
local crypto endpt.: 10.10.10.2, remote crypto endpt.: 10.10.10.1
path mtu 1500, ip mtu 1500
current outbound spi: 0xAD0984CC(2903082188)
inbound esp sas:
spi: 0x533F74A9(1396667561)
transform: esp-des esp-md5-hmac ,
in use settings ={Tunnel, }
conn id: 21, flow_id: SW:21, crypto map: clientmap
sa timing: remaining key lifetime (k/sec): (4470133/2836)
IV size: 8 bytes
replay detection support: Y
Status: ACTIVE
inbound ah sas:
inbound pcp sas:
outbound esp sas:
spi: 0xAD0984CC(2903082188)
transform: esp-des esp-md5-hmac ,
in use settings ={Tunnel, }
conn id: 22, flow_id: SW:22, crypto map: clientmap
sa timing: remaining key lifetime (k/sec): (4470133/2834)
IV size: 8 bytes
replay detection support: Y
Status: ACTIVE
outbound ah sas:
outbound pcp sas:
protected vrf: (none)
local ident (addr/mask/prot/port): (0.0.0.0/0.0.0.0/0/0)
remote ident (addr/mask/prot/port): (172.16.1.0/255.255.255.0/0/0)
current_peer 10.10.10.1 port 500
PERMIT, flags={}
#pkts encaps: 5, #pkts encrypt: 5, #pkts digest: 5
#pkts decaps: 5, #pkts decrypt: 5, #pkts verify: 5
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 0, #pkts compr. failed: 0
#pkts not decompressed: 0, #pkts decompress failed: 0
#send errors 0, #recv errors 0
local crypto endpt.: 10.10.10.2, remote crypto endpt.: 10.10.10.1
path mtu 1500, ip mtu 1500
current outbound spi: 0xC82C0695(3358328469)
inbound esp sas:
spi: 0x2ECA448B(785007755)
transform: esp-des esp-md5-hmac ,
in use settings ={Tunnel, }
conn id: 23, flow_id: SW:23, crypto map: clientmap
sa timing: remaining key lifetime (k/sec): (4589382/2832)
IV size: 8 bytes
replay detection support: Y
Status: ACTIVE
inbound ah sas:
inbound pcp sas:
outbound esp sas:
spi: 0xC82C0695(3358328469)
transform: esp-des esp-md5-hmac ,
in use settings ={Tunnel, }
conn id: 24, flow_id: SW:24, crypto map: clientmap
sa timing: remaining key lifetime (k/sec): (4589382/2830)
IV size: 8 bytes
replay detection support: Y
Status: ACTIVE
outbound ah sas:
outbound pcp sas:
Troubleshoot
Use this section to troubleshoot your configuration.
If you have set up the Easy VPN Remote (PIX) and Easy VPN Server (IOS) as described in this document and are still experiencing problems, please gather the debug output from the PIX and the IOS and output from the show command for analysis by the Cisco Technical Assistance Center (TAC). See also Troubleshooting the PIX to Pass Data Traffic on an Established IPSec Tunnel or IP Security Troubleshooting - Understanding and Using debug Commands. Enable IPSec debugging on the PIX.
PIX debug Commands and Sample Output
PIX debug Commands
Note: Refer to Important Information on Debug Commands before you use debug commands.
- debug crypto ipsec—Displays the IPSec negotiations of Phase 2.
- debug crypto isakmp—Displays the ISAKMP negotiations of Phase 1.
PIX Sample Output
ISAKMP (0): ID payload
next-payload : 13
type : 11
protocol : 17
port : 0
length : 12pix506(config)#
ISAKMP (0): Total payload length: 16
ISAKMP (0:0): sending NAT-T vendor ID - rev 2 & 3
ISAKMP (0): beginning Aggressive Mode exchange
crypto_isakmp_process_block:src:10.10.10.2, dest:10.10.10.1 spt:500 dpt:500
OAK_AG exchange
ISAKMP (0): processing SA payload. message ID = 0
!--- The PIX checks the received proposal against
!--- its dynamically generated policies looking for a match.
ISAKMP (0): Checking ISAKMP transform 1 against priority 65001 policy
ISAKMP: encryption DES-CBC
ISAKMP: hash MD5
ISAKMP: default group 2
ISAKMP: extended auth pre-share (init)
ISAKMP: life type in seconds
ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80
ISAKMP (0): atts are not acceptable. Next payload is 0
ISAKMP (0): Checking ISAKMP transform 1 against priority 65002 policy
ISAKMP: encryption DES-CBC
ISAKMP: hash MD5
ISAKMP: default group 2
ISAKMP: extended auth pre-share (init)
ISAKMP: life type in seconds
ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80
ISAKMP (0): atts are not acceptable. Next payload is 0
ISAKMP (0): Checking ISAKMP transform 1 against priority 65003 policy
ISAKMP: encryption DES-CBC
ISAKMP: hash MD5
ISAKMP: default group 2
ISAKMP: extended auth pre-share (init)
ISAKMP: life type in seconds
ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80
ISAKMP (0): atts are not acceptable. Next payload is 0
ISAKMP (0): Checking ISAKMP transform 1 against priority 65004 policy
ISAKMP: encryption DES-CBC
ISAKMP: hash MD5
ISAKMP: default group 2
ISAKMP: extended auth pre-share (init)
ISAKMP: life type in seconds
ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80
ISAKMP (0): atts are not acceptable. Next payload is 0
ISAKMP (0): Checking ISAKMP transform 1 against priority 65005 policy
ISAKMP: encryption DES-CBC
ISAKMP: hash MD5
ISAKMP: default group 2
ISAKMP: extended auth pre-share (init)
ISAKMP: life type in seconds
ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80
ISAKMP (0): atts are not acceptable. Next payload is 0
ISAKMP (0): Checking ISAKMP transform 1 against priority 65006 policy
ISAKMP: encryption DES-CBC
ISAKMP: hash MD5
ISAKMP: default group 2
ISAKMP: extended auth pre-share (init)
ISAKMP: life type in seconds
ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80
ISAKMP (0): atts are not acceptable. Next payload is 0
ISAKMP (0): Checking ISAKMP transform 1 against priority 65007 policy
ISAKMP: encryption DES-CBC
ISAKMP: hash MD5
ISAKMP: default group 2
ISAKMP: extended auth pre-share (init)
ISAKMP: life type in seconds
ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80
ISAKMP (0): atts are not acceptable. Next payload is 0
ISAKMP (0): Checking ISAKMP transform 1 against priority 65008 policy
ISAKMP: encryption DES-CBC
ISAKMP: hash MD5
ISAKMP: default group 2
ISAKMP: extended auth pre-share (init)
ISAKMP: life type in seconds
ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80
ISAKMP (0): atts are not acceptable. Next payload is 0
ISAKMP (0): Checking ISAKMP transform 1 against priority 65009 policy
ISAKMP: encryption DES-CBC
ISAKMP: hash MD5
ISAKMP: default group 2
ISAKMP: extended auth pre-share (init)
ISAKMP: life type in seconds
ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80
ISAKMP (0): atts are acceptable. Next payload is 0
ISAKMP (0): processing vendor id payload
ISAKMP (0): processing vendor id payload
ISAKMP (0): remote peer supports dead peer detection
ISAKMP (0): processing vendor id payload
crypto_isakmp_process_block:src:10.10.10.2, dest:10.10.10.1 spt:500 dpt:500
crypto_isakmp_process_block:src:10.10.10.2, dest:10.10.10.1 spt:500 dpt:500
ISAKMP : attributes being requested
crypto_isakmp_process_block:src:10.10.10.2, dest:10.10.10.1 spt:500 dpt:500
ISAKMP (0): beginning Quick Mode exchange, M-ID of -582033986:dd4eddbeIPSEC
(key_engine): got a queue event...
IPSEC(spi_response): getting spi 0x61cf8d08(1640992008) for SA
from 10.10.10.2 to 10.10.10.1 for prot 3
crypto_isakmp_process_block:src:10.10.10.2, dest:10.10.10.1 spt:500 dpt:500
OAK_QM exchange
oakley_process_quick_mode:
OAK_QM_IDLE
ISAKMP (0): processing SA payload. message ID = 3712933310
ISAKMP : Checking IPSec proposal 1
ISAKMP: transform 1, ESP_DES
ISAKMP: attributes in transform:
ISAKMP: encaps is 1
ISAKMP: SA life type in seconds
ISAKMP: SA life duration (basic) of 28800
ISAKMP: SA life type in kilobytes
ISAKMP: SA life duration (VPI) of 0x0 0x46 0x50 0x0
ISAKMP: authenticator is HMAC-MD5
ISAKMP (0): atts are acceptable.IPSEC(validate_proposal_request): proposal part #1,
(key eng. msg.) dest= 10.10.10.2, src= 10.10.10.1,
dest_proxy= 0.0.0.0/0.0.0.0/0/0 (type=4),
src_proxy= 10.10.10.1/255.255.255.255/0/0 (type=1),
protocol= ESP, transform= esp-des esp-md5-hmac ,
lifedur= 0s and 0kb,
spi= 0x0(0), conn_id= 0, keysize= 0, flags= 0x4
ISAKMP (0): processing NONCE payload. message ID = 3712933310
ISAKMP (0): processing ID payload. message ID = 3712933310
ISAKMP (0): processing ID payload. message ID = 3712933310
ISAKMP (0): processing NOTIFY payload 24576 protocol 3
spi 1327036890, message ID = 3712933310
ISAKMP (0): processing responder lifetime
ISAKMP (0): responder lifetime of 3600s
ISAKMP (0): Creating IPSec SAs
inbound SA from 10.10.10.2 to 10.10.10.1 (proxy 0.0.0.0 to 10.10.10.1)
has spi 1640992008 and conn_id 1 and flags 4
lifetime of 3600 seconds
lifetime of 4608000 kilobytes
outbound SA from 10.10.10.1 to 10.10.10.2 (proxy 10.10.10.1 to 0.0.0.0)
has spi 1327036890 and conn_id 2 and flags 4
lifetime of 3600 seconds
lifetime of 4608000 kilobytesIPSEC(key_engine): got a queue event...
IPSEC(initialize_sas): ,
(key eng. msg.) dest= 10.10.10.1, src= 10.10.10.2,
dest_proxy= 10.10.10.1/255.255.255.255/0/0 (type=1),
src_proxy= 0.0.0.0/0.0.0.0/0/0 (type=4),
protocol= ESP, transform= esp-des esp-md5-hmac ,
lifedur= 3600s and 4608000kb,
spi= 0x61cf8d08(1640992008), conn_id= 1, keysize= 0, flags= 0x4
IPSEC(initialize_sas): ,
(key eng. msg.) src= 10.10.10.1, dest= 10.10.10.2,
src_proxy= 10.10.10.1/255.255.255.255/0/0 (type=1),
dest_proxy= 0.0.0.0/0.0.0.0/0/0 (type=4),
protocol= ESP, transform= esp-des esp-md5-hmac ,
lifedur= 3600s and 4608000kb,
spi= 0x4f18f9da(1327036890), conn_id= 2, keysize= 0, flags= 0x4
!--- The IPSec SAs shown above are for management purposes.
VPN Peer: IPSEC: Peer ip:10.10.10.2/500 Ref cnt incremented to:2 Total VPN Peers:1
VPN Peer: IPSEC: Peer ip:10.10.10.2/500 Ref cnt incremented to:3 Total VPN Peers:1
return status is IKMP_NO_ERROR
ISAKMP (0): beginning Quick Mode exchange, M-ID of -419501328:e6feeaf0IPSEC
(key_engine): got a queue event...
IPSEC(spi_response): getting spi 0xf3d52246(4090831430) for SA
from 10.10.10.2 to 10.10.10.1 for prot 3
crypto_isakmp_process_block:src:10.10.10.2, dest:10.10.10.1 spt:500 dpt:500
OAK_QM exchange
oakley_process_quick_mode:
OAK_QM_IDLE
ISAKMP (0): processing SA payload. message ID = 3875465968
ISAKMP : Checking IPSec proposal 1
ISAKMP: transform 1, ESP_DES
ISAKMP: attributes in transform:
ISAKMP: encaps is 1
ISAKMP: SA life type in seconds
ISAKMP: SA life duration (basic) of 28800
ISAKMP: SA life type in kilobytes
ISAKMP: SA life duration (VPI) of 0x0 0x46 0x50 0x0
ISAKMP: authenticator is HMAC-MD5
ISAKMP (0): atts are acceptable.IPSEC(validate_proposal_request): proposal part #1,
(key eng. msg.) dest= 10.10.10.2, src= 10.10.10.1,
dest_proxy= 0.0.0.0/0.0.0.0/0/0 (type=4),
src_proxy= 172.16.1.0/255.255.255.0/0/0 (type=4),
protocol= ESP, transform= esp-des esp-md5-hmac ,
lifedur= 0s and 0kb,
spi= 0x0(0), conn_id= 0, keysize= 0, flags= 0x4
ISAKMP (0): processing NONCE payload. message ID = 3875465968
ISAKMP (0): processing ID payload. message ID = 3875465968
ISAKMP (0): processing ID payload. message ID = 3875465968
ISAKMP (0): processing NOTIFY payload 24576 protocol 3
spi 465396864, message ID = 3875465968
ISAKMP (0): processing responder lifetime
ISAKMP (0): responder lifetime of 3600s
ISAKMP (0): Creating IPSec SAs
inbound SA from 10.10.10.2 to 10.10.10.1 (proxy 0.0.0.0 to 172.16.1.0)
has spi 4090831430 and conn_id 3 and flags 4
lifetime of 3600 seconds
lifetime of 4608000 kilobytes
outbound SA from 10.10.10.1 to 10.10.10.2 (proxy 172.16.1.0 to 0.0.0.0)
has spi 465396864 and conn_id 4 and flags 4
lifetime of 3600 seconds
lifetime of 4608000 kilobytesIPSEC(key_engine): got a queue event...
IPSEC(initialize_sas): ,
(key eng. msg.) dest= 10.10.10.1, src= 10.10.10.2,
dest_proxy= 172.16.1.0/255.255.255.0/0/0 (type=4),
src_proxy= 0.0.0.0/0.0.0.0/0/0 (type=4),
protocol= ESP, transform= esp-des esp-md5-hmac ,
lifedur= 3600s and 4608000kb,
spi= 0xf3d52246(4090831430), conn_id= 3, keysize= 0, flags= 0x4
IPSEC(initialize_sas): ,
(key eng. msg.) src= 10.10.10.1, dest= 10.10.10.2,
src_proxy= 172.16.1.0/255.255.255.0/0/0 (type=4),
dest_proxy= 0.0.0.0/0.0.0.0/0/0 (type=4),
protocol= ESP, transform= esp-des esp-md5-hmac ,
lifedur= 3600s and 4608000kb,
spi= 0x1bbd6480(465396864), conn_id= 4, keysize= 0, flags= 0x4
!--- The IPSec SAs shown above are for actual data traffic.
VPN Peer: IPSEC: Peer ip:10.10.10.2/500 Ref cnt incremented to:4 Total VPN Peers:1
VPN Peer: IPSEC: Peer ip:10.10.10.2/500 Ref cnt incremented to:5 Total VPN Peers:1
IOS debug Commands and Sample Output
IOS debug Commands
Note: Refer to Important Information on Debug Commands before you use debug commands.
- debug crypto ipsec—Displays detailed IPSec events.
- debug crypto isakmp—Displays messages about IKE events.
- debug crypto engine—Displays the traffic that is encrypted.
IOS Sample Output
!--- As soon as the vpnclient enable command is issued on the PIX,
!--- the IOS device receives an IKE negotiation request.
*Jan 20 16:48:22.267: ISAKMP (0:0): received packet from 10.10.10.1 dport
500 sport 500 Global (N) NEW
SA
*Jan 20 16:48:22.271: ISAKMP: Created a peer struct for 10.10.10.1,
peer port 500
*Jan 20 16:48:22.271: ISAKMP: New peer created peer = 0x6758C6D0
peer_handle = 0x80000026
*Jan 20 16:48:22.271: ISAKMP: Locking peer struct 0x6758C6D0,
refcount 1 for
crypto_isakmp_process_block
*Jan 20 16:48:22.271: ISAKMP:(0):Setting client config settings 6679B340
*Jan 20 16:48:22.271: ISAKMP:(0):(Re)Setting client xauth list and state
*Jan 20 16:48:22.271: ISAKMP/xauth: initializing AAA request
*Jan 20 16:48:22.271: ISAKMP: local port 500, remote port 500
*Jan 20 16:48:22.271: insert sa successfully sa = 658E0874
*Jan 20 16:48:22.271: ISAKMP:(0): processing SA payload. message ID = 0
*Jan 20 16:48:22.271: ISAKMP:(0): processing ID payload. message ID = 0
*Jan 20 16:48:22.271: ISAKMP (0:0): ID payload
next-payload : 13
type : 11
group id : hwclient
protocol : 17
port : 0
length : 16
*Jan 20 16:48:22.271: ISAKMP:(0):: peer matches *none* of the profiles
*Jan 20 16:48:22.271: ISAKMP:(0): processing vendor id payload
*Jan 20 16:48:22.271: ISAKMP:(0): vendor ID seems Unity/DPD but
major 215 mismatch
*Jan 20 16:48:22.271: ISAKMP:(0): vendor ID is XAUTH
*Jan 20 16:48:22.271: ISAKMP:(0): processing vendor id payload
*Jan 20 16:48:22.271: ISAKMP:(0): vendor ID is DPD
*Jan 20 16:48:22.271: ISAKMP:(0): processing vendor id payload
*Jan 20 16:48:22.271: ISAKMP:(0): claimed IOS but failed authentication
*Jan 20 16:48:22.271: ISAKMP:(0): processing vendor id payload
*Jan 20 16:48:22.271: ISAKMP:(0): vendor ID is Unity
*Jan 20 16:48:22.271: ISAKMP:(0): Authentication by xauth preshared
*Jan 20 16:48:22.271: ISAKMP:(0):Checking ISAKMP transform 1 against
priority 10 policy
*Jan 20 16:48:22.271: ISAKMP: encryption AES-CBC
*Jan 20 16:48:22.271: ISAKMP: keylength of 256
*Jan 20 16:48:22.271: ISAKMP: hash SHA
*Jan 20 16:48:22.271: ISAKMP: default group 2
*Jan 20 16:48:22.271: ISAKMP: auth XAUTHInitPreShared
*Jan 20 16:48:22.271: ISAKMP: life type in seconds
*Jan 20 16:48:22.271: ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80
*Jan 20 16:48:22.271: ISAKMP:(0):Encryption algorithm offered does
not match policy!
*Jan 20 16:48:22.271: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Jan 20 16:48:22.271: ISAKMP:(0):Checking ISAKMP transform 2 against
priority 10 policy
*Jan 20 16:48:22.271: ISAKMP: encryption AES-CBC
*Jan 20 16:48:22.275: ISAKMP: keylength of 256
*Jan 20 16:48:22.275: ISAKMP: hash MD5
*Jan 20 16:48:22.275: ISAKMP: default group 2
*Jan 20 16:48:22.275: ISAKMP: auth XAUTHInitPreShared
*Jan 20 16:48:22.275: ISAKMP: life type in seconds
*Jan 20 16:48:22.275: ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80
*Jan 20 16:48:22.275: ISAKMP:(0):Encryption algorithm offered
does not match policy!
*Jan 20 16:48:22.275: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Jan 20 16:48:22.275: ISAKMP:(0):Checking ISAKMP transform 3 against
priority 10 policy
*Jan 20 16:48:22.275: ISAKMP: encryption AES-CBC
*Jan 20 16:48:22.275: ISAKMP: keylength of 192
*Jan 20 16:48:22.275: ISAKMP: hash SHA
*Jan 20 16:48:22.275: ISAKMP: default group 2
*Jan 20 16:48:22.275: ISAKMP: auth XAUTHInitPreShared
*Jan 20 16:48:22.275: ISAKMP: life type in seconds
*Jan 20 16:48:22.275: ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80
*Jan 20 16:48:22.275: ISAKMP:(0):Encryption algorithm offered
does not match policy!
*Jan 20 16:48:22.275: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Jan 20 16:48:22.275: ISAKMP:(0):Checking ISAKMP transform 4 against
priority 10 policy
*Jan 20 16:48:22.275: ISAKMP: encryption AES-CBC
*Jan 20 16:48:22.275: ISAKMP: keylength of 192
*Jan 20 16:48:22.275: ISAKMP: hash MD5
*Jan 20 16:48:22.275: ISAKMP: default group 2
*Jan 20 16:48:22.275: ISAKMP: auth XAUTHInitPreShared
*Jan 20 16:48:22.275: ISAKMP: life type in seconds
*Jan 20 16:48:22.275: ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80
*Jan 20 16:48:22.275: ISAKMP:(0):Encryption algorithm offered
does not match policy!
*Jan 20 16:48:22.275: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Jan 20 16:48:22.275: ISAKMP:(0):Checking ISAKMP transform 5 against
priority 10 policy
*Jan 20 16:48:22.275: ISAKMP: encryption AES-CBC
*Jan 20 16:48:22.275: ISAKMP: keylength of 128
*Jan 20 16:48:22.275: ISAKMP: hash SHA
*Jan 20 16:48:22.275: ISAKMP: default group 2
*Jan 20 16:48:2f 0x0 0x1 0x51 0x80
*Jan 20 16:48:22.275: ISAKMP:(0):Encryption algorithm offered
does not match policy!
*Jan 20 16:48:22.275: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Jan 20 16:48:22.275: ISAKMP:(0):Checking ISAKMP transform 6 against
priority 10 policy
*Jan 20 16:48:22.275: ISAKMP: encryption AES-CBC
*Jan 20 16:48:22.275: ISAKMP: keylength of 128
*Jan 20 16:48:22.275: ISAKMP: hash MD52.275: ISAKMP:
auth XAUTHInitPreShared
*Jan 20 16:48:22.275: ISAKMP: life type in seconds
*Jan 20 16:48:22.275: ISAKMP: life duration (VPI) o
*Jan 20 16:48:22.275: ISAKMP: default group 2
*Jan 20 16:48:22.275: ISAKMP: auth XAUTHInitPreShared
*Jan 20 16:48:22.275: ISAKMP: life type in seconds
*Jan 20 16:48:22.275: ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80
*Jan 20 16:48:22.275: ISAKMP:(0):Encryption algorithm offered
does not match policy!
*Jan 20 16:48:22.275: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Jan 20 16:48:22.275: ISAKMP:(0):Checking ISAKMP transform 7 against
priority 10 policy
*Jan 20 16:48:22.275: ISAKMP: encryption 3DES-CBC
*Jan 20 16:48:22.275: ISAKMP: hash SHA
*Jan 20 16:48:22.275: ISAKMP: default group 2
*Jan 20 16:48:22.275: ISAKMP: auth XAUTHInitPreShared
*Jan 20 16:48:22.279: ISAKMP: life type in seconds
*Jan 20 16:48:22.279: ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80
*Jan 20 16:48:22.279: ISAKMP:(0):Encryption algorithm offered
does not match policy!
*Jan 20 16:48:22.279: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Jan 20 16:48:22.279: ISAKMP:(0):Checking ISAKMP transform 8 against
priority 10 policy
*Jan 20 16:48:22.279: ISAKMP: encryption 3DES-CBC
*Jan 20 16:48:22.279: ISAKMP: hash MD5
*Jan 20 16:48:22.279: ISAKMP: default group 2
*Jan 20 16:48:22.279: ISAKMP: auth XAUTHInitPreShared
*Jan 20 16:48:22.279: ISAKMP: life type in seconds
*Jan 20 16:48:22.279: ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80
*Jan 20 16:48:22.279: ISAKMP:(0):Encryption algorithm offered
does not match policy!
*Jan 20 16:48:22.279: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Jan 20 16:48:22.279: ISAKMP:(0):Checking ISAKMP transform 9 against
priority 10 policy
*Jan 20 16:48:22.279: ISAKMP: encryption DES-CBC
*Jan 20 16:48:22.279: ISAKMP: hash MD5
*Jan 20 16:48:22.279: ISAKMP: default group 2
*Jan 20 16:48:22.279: ISAKMP: auth XAUTHInitPreShared
*Jan 20 16:48:22.279: ISAKMP: life type in seconds
*Jan 20 16:48:22.279: ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80
*Jan 20 16:48:22.279: ISAKMP:(0):atts are acceptable. Next payload is 3
!--- Both the IOS device and the PIX accept the policy for ISAKMP.
*Jan 20 16:48:22.279: ISAKMP:(0): processing KE payload. message ID = 0
*Jan 20 16:48:22.279: crypto_engine: Create DH shared secret
*Jan 20 16:48:22.279: crypto_engine: Modular Exponentiation
*Jan 20 16:48:22.319: ISAKMP:(0): processing NONCE payload. message ID = 0
*Jan 20 16:48:22.319: ISAKMP:(0): vendor ID is NAT-T v3
*Jan 20 16:48:22.319: ISAKMP:(0): vendor ID is NAT-T v2
*Jan 20 16:48:22.319: ISAKMP:(0):Input = IKE_MESG_FROM_PEER, IKE_AM_EXCH
*Jan 20 16:48:22.319: ISAKMP:(0):Old State = IKE_READY
New State = IKE_R_AM_AAA_AWAIT
*Jan 20 16:48:22.319: crypto_engine: Create IKE SA
*Jan 20 16:48:22.319: crypto engine: deleting DH phase 2 SW:38
*Jan 20 16:48:22.319: crypto_engine: Delete DH shared secret
*Jan 20 16:48:22.319: ISAKMP:(1030): constructed NAT-T vendor-03 ID
*Jan 20 16:48:22.319: ISAKMP:(1030):SA is doing pre-shared key
authentication plus XAUTH using id type
ID_IPV4_ADDR
*Jan 20 16:48:22.323: ISAKMP (0:1030): ID payload
next-payload : 10
type : 1
address : 10.10.10.2
protocol : 17
port : 0
length : 12
*Jan 20 16:48:22.323: ISAKMP:(1030):Total payload length: 12
*Jan 20 16:48:22.323: crypto_engine: Generate IKE hash
*Jan 20 16:48:22.323: ISAKMP:(1030): sending packet to 10.10.10.1
my_port 500 peer_port 500 (R)
AG_INIT_EXCH
*Jan 20 16:48:22.323: ISAKMP:(1030):Input = IKE_MESG_FROM_AAA,
PRESHARED_KEY_REPLY
*Jan 20 16:48:22.323: ISAKMP:(1030):Old State = IKE_R_AM_AAA_AWAIT
New State = IKE_R_AM2
*Jan 20 16:48:22.479: ISAKMP (0:1030): received packet from 10.10.10.1 dport
500 sport 500 Global (R)
AG_INIT_EXCH
*Jan 20 16:48:22.479: crypto_engine: Decrypt IKE packet
*Jan 20 16:48:22.479: ISAKMP:received payload type 20
*Jan 20 16:48:22.479: ISAKMP:received payload type 20
*Jan 20 16:48:22.479: ISAKMP:(1030): processing HASH payload. message ID = 0
*Jan 20 16:48:22.479: crypto_engine: Generate IKE hash
*Jan 20 16:48:22.483: ISAKMP:(1030): processing NOTIFY INITIAL_CONTACT
protocol 1
spi 0, message ID = 0, sa = 658E0874
*Jan 20 16:48:22.483: ISAKMP:(1030):SA authentication status:
authenticated
*Jan 20 16:48:22.483: ISAKMP:(1030):SA has been authenticated with 10.10.10.1
*Jan 20 16:48:22.483: ISAKMP:(1030):SA authentication status:
authenticated
*Jan 20 16:48:22.483: ISAKMP:(1030): Process initial contact,
bring down existing phase 1 and 2 SA's with local 10.10.10.2 remote 10.10.10.1
remote port 500
*Jan 20 16:48:22.483: ISAKMP:(1030):returning IP addr to the address pool
*Jan 20 16:48:22.483: ISAKMP: Trying to insert a peer 10.10.10.2/10.10.10.1/500/,
and inserted successfully 6758C6D0.
*Jan 20 16:48:22.483: IPSEC(key_engine): got a queue event with 1 KMI message(s)
*Jan 20 16:48:22.483: ISAKMP: set new node -1980405900 to CONF_XAUTH
*Jan 20 16:48:22.483: crypto_engine: Generate IKE hash
*Jan 20 16:48:22.483: ISAKMP:(1030):Sending NOTIFY RESPONDER_LIFETIME protocol 1
spi 1727476520, message ID = -1980405900
*Jan 20 16:48:22.483: crypto_engine: Encrypt IKE packet
*Jan 20 16:48:22.483: ISAKMP:(1030): sending packet to 10.10.10.1 my_port
500 peer_port 500 (R)
QM_IDLE
*Jan 20 16:48:22.483: ISAKMP:(1030):purging node -1980405900
*Jan 20 16:48:22.483: ISAKMP: Sending phase 1 responder lifetime 86400
*Jan 20 16:48:22.483: ISAKMP:(1030):Input = IKE_MESG_FROM_PEER, IKE_AM_EXCH
*Jan 20 16:48:22.483: ISAKMP:(1030):Old State = IKE_R_AM2
New State = IKE_P1_COMPLETE
*Jan 20 16:48:22.483: ISAKMP:(1030):Need XAUTH
!--- The IOS device now processes the Extended Authentication phase
!--- after Phase 1 is successful.
*Jan 20 16:48:22.483: ISAKMP: set new node -791275911 to CONF_XAUTH
*Jan 20 16:48:22.487: ISAKMP/xauth: request attribute XAUTH_USER_NAME_V2
*Jan 20 16:48:22.487: ISAKMP/xauth: request attribute XAUTH_USER_PASSWORD_V2
*Jan 20 16:48:22.487: crypto_engine: Generate IKE hash
*Jan 20 16:48:22.487: ISAKMP:(1030): initiating peer config to 10.10.10.1.
ID = -791275911
*Jan 20 16:48:22.487: crypto_engine: Encrypt IKE packet
*Jan 20 16:48:22.487: ISAKMP:(1030): sending packet to 10.10.10.1 my_port
500 peer_port 500 (R)
CONF_XAUTH
*Jan 20 16:48:22.487: ISAKMP:(1030):Input = IKE_MESG_INTERNAL,
IKE_PHASE1_COMPLETE
*Jan 20 16:48:22.487: ISAKMP:(1030):Old State = IKE_P1_COMPLETE
New State = IKE_XAUTH_REQ_SENT
*Jan 20 16:48:22.519: ISAKMP (0:1030): received packet from 10.10.10.1 dport
500 sport 500 Global (R)
CONF_XAUTH
*Jan 20 16:48:22.519: crypto_engine: Decrypt IKE packet
*Jan 20 16:48:22.519: ISAKMP:(1030):processing transaction payload
from 10.10.10.1. message ID =
-791275911
*Jan 20 16:48:22.519: crypto_engine: Generate IKE hash
*Jan 20 16:48:22.519: ISAKMP: Config payload REPLY
*Jan 20 16:48:22.519: ISAKMP/xauth: reply attribute XAUTH_USER_NAME_V2
*Jan 20 16:48:22.519: ISAKMP/xauth: reply attribute XAUTH_USER_PASSWORD_V2
*Jan 20 16:48:22.519: ISAKMP:(1030):deleting node -791275911
error FALSE reason "Done with xauth
request/reply exchange"
*Jan 20 16:48:22.519: ISAKMP:(1030):Input = IKE_MESG_FROM_PEER, IKE_CFG_REPLY
*Jan 20 16:48:22.519: ISAKMP:(1030):Old State = IKE_XAUTH_REQ_SENT New State =
IKE_XAUTH_AAA_CONT_LOGIN_AWAIT
*Jan 20 16:48:22.519: ISAKMP: set new node 44674085 to CONF_XAUTH
*Jan 20 16:48:22.519: crypto_engine: Generate IKE hash
*Jan 20 16:48:22.519: ISAKMP:(1030): initiating peer config to 10.10.10.1.
ID = 44674085
*Jan 20 16:48:22.519: crypto_engine: Encrypt IKE packet
*Jan 20 16:48:22.519: ISAKMP:(1030): sending packet to 10.10.10.1 my_port
500 peer_port 500 (R)
CONF_XAUTH
*Jan 20 16:48:22.519: ISAKMP:(1030):Input = IKE_MESG_FROM_AAA,
IKE_AAA_CONT_LOGIN
*Jan 20 16:48:22.519: ISAKMP:(1030):Old State = IKE_XAUTH_AAA_CONT_LOGIN_AWAIT
New State =
IKE_XAUTH_SET_SENT
*Jan 20 16:48:22.571: ISAKMP (0:1030): received packet from 10.10.10.1 dport
500 sport 500 Global (R)
CONF_XAUTH
*Jan 20 16:48:22.571: crypto_engine: Decrypt IKE packet
*Jan 20 16:48:22.571: ISAKMP:(1030):processing transaction payload
from 10.10.10.1. message ID =
44674085
*Jan 20 16:48:22.571: crypto_engine: Generate IKE hash
*Jan 20 16:48:22.571: ISAKMP: Config payload ACK
*Jan 20 16:48:22.571: ISAKMP:(1030): XAUTH ACK Processed
*Jan 20 16:48:22.571: ISAKMP:(1030):deleting node 44674085
error FALSE reason "Transaction mode done"
*Jan 20 16:48:22.571: ISAKMP:(1030):Input = IKE_MESG_FROM_PEER, IKE_CFG_ACK
*Jan 20 16:48:22.571: ISAKMP:(1030):Old State = IKE_XAUTH_SET_SENT
New State = IKE_P1_COMPLETE
*Jan 20 16:48:22.571: ISAKMP:(1030):Input = IKE_MESG_INTERNAL,
IKE_PHASE1_COMPLETE
*Jan 20 16:48:22.571: ISAKMP:(1030):Old State = IKE_P1_COMPLETE
New State = IKE_P1_COMPLETE
!--- Extended authentication is complete,
!--- and mode configuration is now processed.
*Jan 20 16:48:22.619: ISAKMP (0:1030): received packet from 10.10.10.1 dport
500 sport 500 Global (R)
QM_IDLE
*Jan 20 16:48:22.619: ISAKMP: set new node -2005047200 to QM_IDLE
*Jan 20 16:48:22.619: crypto_engine: Decrypt IKE packet
*Jan 20 16:48:22.623: ISAKMP:(1030):processing transaction payload
from 10.10.10.1. message ID =
-2005047200
*Jan 20 16:48:22.623: crypto_engine: Generate IKE hash
*Jan 20 16:48:22.623: ISAKMP: Config payload REQUEST
*Jan 20 16:48:22.623: ISAKMP:(1030):checking request:
*Jan 20 16:48:22.623: ISAKMP: DEFAULT_DOMAIN
*Jan 20 16:48:22.623: ISAKMP: IP4_NBNS
*Jan 20 16:48:22.623: ISAKMP: IP4_DNS
*Jan 20 16:48:22.623: ISAKMP: SPLIT_INCLUDE
*Jan 20 16:48:22.623: ISAKMP: SPLIT_DNS
*Jan 20 16:48:22.623: ISAKMP: PFS
*Jan 20 16:48:22.623: ISAKMP: CONFIG_MODE_UNKNOWN Unknown Attr: 0x7800
*Jan 20 16:48:22.623: ISAKMP: CONFIG_MODE_UNKNOWN Unknown Attr: 0x7801
*Jan 20 16:48:22.623: ISAKMP: CONFIG_MODE_UNKNOWN Unknown Attr: 0x7802
*Jan 20 16:48:22.623: ISAKMP: CONFIG_MODE_UNKNOWN Unknown Attr: 0x7803
*Jan 20 16:48:22.623: ISAKMP: CONFIG_MODE_UNKNOWN Unknown Attr: 0x7804
*Jan 20 16:48:22.623: ISAKMP: CONFIG_MODE_UNKNOWN Unknown Attr: 0x7805
*Jan 20 16:48:22.623: ISAKMP: CONFIG_MODE_UNKNOWN Unknown Attr: 0x7806
*Jan 20 16:48:22.623: ISAKMP: BACKUP_SERVER
*Jan 20 16:48:22.623: ISAKMP: APPLICATION_VERSION
*Jan 20 16:48:22.623: ISAKMP/author: Author request for group
hw client successfully sent to AAA
*Jan 20 16:48:22.623: ISAKMP:(1030):Input = IKE_MESG_FROM_PEER,
IKE_CFG_REQUEST
*Jan 20 16:48:22.623: ISAKMP:(1030):Old State = IKE_P1_COMPLETE
New State = IKE_CONFIG_AUTHOR_AAA_AWAIT
*Jan 20 16:48:22.623: ISAKMP:(1030):attributes sent in message:
*Jan 20 16:48:22.623: ISAKMP: Sending DEFAULT_DOMAIN default domain name: cisco.com
*Jan 20 16:48:22.623: ISAKMP: Sending IP4_NBNS server address: 172.22.1.102
*Jan 20 16:48:22.623: ISAKMP: Sending IP4_DNS server address: 172.22.1.101
*Jan 20 16:48:22.623: ISAKMP (0/1030): Unknown Attr: CONFIG_MODE_UNKNOWN (0x7800)
*Jan 20 16:48:22.623: ISAKMP (0/1030): Unknown Attr: CONFIG_MODE_UNKNOWN (0x7801)
*Jan 20 16:48:22.623: ISAKMP (0/1030): Unknown Attr: CONFIG_MODE_UNKNOWN (0x7802)
*Jan 20 16:48:22.623: ISAKMP (0/1030): Unknown Attr: CONFIG_MODE_UNKNOWN (0x7803)
*Jan 20 16:48:22.623: ISAKMP (0/1030): Unknown Attr: CONFIG_MODE_UNKNOWN (0x7804)
*Jan 20 16:48:22.623: ISAKMP (0/1030): Unknown Attr: CONFIG_MODE_UNKNOWN (0x7805)
*Jan 20 16:48:22.627: ISAKMP (0/1030): Unknown Attr: CONFIG_MODE_UNKNOWN (0x7806)
*Jan 20 16:48:22.627: ISAKMP: Sending APPLICATION_VERSION string:
Cisco IOS Software, 7200 Software
(C7200-ADVENTERPRISEK9-M), Version 12.4(4)T1, RELEASE SOFTWARE (fc4)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by Cisco Systems, Inc.
Compiled Wed 21-Dec-05 22:58 by ccai
*Jan 20 16:48:22.627: crypto_engine: Generate IKE hash
*Jan 20 16:48:22.627: ISAKMP:(1030): responding to peer config
from 10.10.10.1. ID = -2005047200
*Jan 20 16:48:22.627: crypto_engine: Encrypt IKE packet
*Jan 20 16:48:22.627: ISAKMP:(1030): sending packet to 10.10.10.1
my_port 500 peer_port 500 (R)
CONF_ADDR
*Jan 20 16:48:22.627: ISAKMP:(1030):deleting node -2005047200
error FALSE reason "No Error"
*Jan 20 16:48:22.627: ISAKMP:(1030):Input = IKE_MESG_FROM_AAA, IKE_AAA_GROUP_ATTR
*Jan 20 16:48:22.627: ISAKMP:(1030):Old State = IKE_CONFIG_AUTHOR_AAA_AWAIT
New State =
IKE_P1_COMPLETE
*Jan 20 16:48:22.627: ISAKMP:(1030):Input = IKE_MESG_INTERNAL,
IKE_PHASE1_COMPLETE
*Jan 20 16:48:22.627: ISAKMP:(1030):Old State = IKE_P1_COMPLETE
New State = IKE_P1_COMPLETE
*Jan 20 16:48:27.695: ISAKMP (0:1030): received packet from 10.10.10.1 dport
500 sport 500 Global (R)
QM_IDLE
*Jan 20 16:48:27.695: ISAKMP: set new node 1887305923 to QM_IDLE
*Jan 20 16:48:27.695: crypto_engine: Decrypt IKE packet
*Jan 20 16:48:27.699: crypto_engine: Generate IKE hash
*Jan 20 16:48:27.699: ISAKMP:(1030): processing HASH payload.
message ID = 1887305923
*Jan 20 16:48:27.699: ISAKMP:(1030): processing SA payload.
message ID = 1887305923
*Jan 20 16:48:27.699: ISAKMP:(1030):Checking IPSec proposal 1
*Jan 20 16:48:27.699: ISAKMP: transform 1, ESP_AES
*Jan 20 16:48:27.699: ISAKMP: attributes in transform:
*Jan 20 16:48:27.699: ISAKMP: encaps is 1 (Tunnel)
*Jan 20 16:48:27.699: ISAKMP: SA life type in seconds
*Jan 20 16:48:27.699: ISAKMP: SA life duration (basic) of 28800
*Jan 20 16:48:27.699: ISAKMP: SA life type in kilobytes
*Jan 20 16:48:27.699: ISAKMP: SA life duration (VPI) of
0x0 0x46 0x50 0x0
*Jan 20 16:48:27.699: ISAKMP: authenticator is HMAC-SHA
*Jan 20 16:48:27.699: ISAKMP: key length is 256
*Jan 20 16:48:27.699: CryptoEngine0: validate proposal
*Jan 20 16:48:27.699: ISAKMP:(1030):atts are acceptable.
*Jan 20 16:48:27.699: IPSEC(validate_proposal_request): proposal part #1
*Jan 20 16:48:27.699: IPSEC(validate_proposal_request): proposal part #1,
(key eng. msg.) INBOUND local= 10.10.10.2, remote= 10.10.10.1,
local_proxy= 0.0.0.0/0.0.0.0/0/0 (type=4),
remote_proxy= 10.10.10.1/255.255.255.255/0/0 (type=1),
protocol= ESP, transform= esp-aes 256 esp-sha-hmac (Tunnel),
lifedur= 0s and 0kb,
spi= 0x0(0), conn_id= 0, keysize= 256, flags= 0x0
*Jan 20 16:48:27.699: IPSEC(crypto_ipsec_process_proposal):
transform proposal not supported for
identity:
{esp-aes 256 esp-sha-hmac }
*Jan 20 16:48:27.699: ISAKMP:(1030): IPSec policy invalidated proposal
*Jan 20 16:48:27.699: ISAKMP:(1030):Checking IPSec proposal 2
*Jan 20 16:48:27.699: ISAKMP: transform 1, ESP_AES
*Jan 20 16:48:27.699: ISAKMP: attributes in transform:
*Jan 20 16:48:27.699: ISAKMP: encaps is 1 (Tunnel)
*Jan 20 16:48:27.699: ISAKMP: SA life type in seconds
*Jan 20 16:48:27.699: ISAKMP: SA life duration (basic) of 28800
*Jan 20 16:48:27.699: ISAKMP: SA life type in kilobytes
*Jan 20 16:48:27.699: ISAKMP: SA life duration (VPI) of 0x0 0x46 0x50 0x0
*Jan 20 16:48:27.699: ISAKMP: authenticator is HMAC-MD5
*Jan 20 16:48:27.699: ISAKMP: key length is 256
*Jan 20 16:48:27.699: CryptoEngine0: validate proposal
*Jan 20 16:48:27.699: ISAKMP:(1030):atts are acceptable.
!--- Proceed for processing Phase 2.
*Jan 20 16:48:27.699: IPSEC(validate_proposal_request): proposal part #1
*Jan 20 16:48:27.699: IPSEC(validate_proposal_request): proposal part #1,
(key eng. msg.) INBOUND local= 10.10.10.2, remote= 10.10.10.1,
local_proxy= 0.0.0.0/0.0.0.0/0/0 (type=4),
remote_proxy= 10.10.10.1/255.255.255.255/0/0 (type=1),
protocol= ESP, transform= esp-aes 256 esp-md5-hmac (Tunnel),
lifedur= 0s and 0kb,
spi= 0x0(0), conn_id= 0, keysize= 256, flags= 0x0
*Jan 20 16:48:27.699: IPSEC(crypto_ipsec_process_proposal):
transform proposal not supported for
identity:
{esp-aes 256 esp-md5-hmac }
*Jan 20 16:48:27.699: ISAKMP:(1030): IPSec policy invalidated proposal
*Jan 20 16:48:27.703: ISAKMP:(1030):Checking IPSec proposal 3
*Jan 20 16:48:27.703: ISAKMP: transform 1, ESP_AES
*Jan 20 16:48:27.703: ISAKMP: attributes in transform:
*Jan 20 16:48:27.703: ISAKMP: encaps is 1 (Tunnel)
*Jan 20 16:48:27.703: ISAKMP: SA life type in seconds
*Jan 20 16:48:27.703: ISAKMP: SA life duration (basic) of 28800
*Jan 20 16:48:27.703: ISAKMP: SA life type in kilobytes
*Jan 20 16:48:27.703: ISAKMP: SA life duration (VPI) of 0x0 0x46 0x50 0x0
*Jan 20 16:48:27.703: ISAKMP: authenticator is HMAC-SHA
*Jan 20 16:48:27.703: ISAKMP: key length is 192
*Jan 20 16:48:27.703: CryptoEngine0: validate proposal
*Jan 20 16:48:27.703: ISAKMP:(1030):atts are acceptable.
*Jan 20 16:48:27.703: IPSEC(validate_proposal_request): proposal part #1
*Jan 20 16:48:27.703: IPSEC(validate_proposal_request): proposal part #1,
(key eng. msg.) INBOUND local= 10.10.10.2, remote= 10.10.10.1,
local_proxy= 0.0.0.0/0.0.0.0/0/0 (type=4),
remote_proxy= 10.10.10.1/255.255.255.255/0/0 (type=1),
protocol= ESP, transform= esp-aes 192 esp-sha-hmac (Tunnel),
lifedur= 0s and 0kb,
spi= 0x0(0), conn_id= 0, keysize= 192, flags= 0x0
*Jan 20 16:48:27.703: IPSEC(crypto_ipsec_process_proposal):
transform proposal not supported for
identity:
{esp-aes 192 esp-sha-hmac }
*Jan 20 16:48:27.703: ISAKMP:(1030): IPSec policy invalidated proposal
*Jan 20 16:48:27.703: ISAKMP:(1030):Checking IPSec proposal 4
*Jan 20 16:48:27.703: ISAKMP: transform 1, ESP_AES
*Jan 20 16:48:27.703: ISAKMP: attributes in transform:
*Jan 20 16:48:27.703: ISAKMP: encaps is 1 (Tunnel)
*Jan 20 16:48:27.703: ISAKMP: SA life type in seconds
*Jan 20 16:48:27.703: ISAKMP: SA life duration (basic) of 28800
*Jan 20 16:48:27.703: ISAKMP: SA life type in kilobytes
*Jan 20 16:48:27.703: ISAKMP: SA life duration (VPI) of 0x0 0x46 0x50 0x0
*Jan 20 16:48:27.703: ISAKMP: authenticator is HMAC-MD5
*Jan 20 16:48:27.703: ISAKMP: key length is 192
*Jan 20 16:48:27.703: CryptoEngine0: validate proposal
*Jan 20 16:48:27.703: ISAKMP:(1030):atts are acceptable.
*Jan 20 16:48:27.703: IPSEC(validate_proposal_request): proposal part #1
*Jan 20 16:48:27.703: IPSEC(validate_proposal_request): proposal part #1,
(key eng. msg.) INBOUND local= 10.10.10.2, remote= 10.10.10.1,
local_proxy= 0.0.0.0/0.0.0.0/0/0 (type=4),
remote_proxy= 10.10.10.1/255.255.255.255/0/0 (type=1),
protocol= ESP, transform= esp-aes 192 esp-md5-hmac (Tunnel),
lifedur= 0s and 0kb,
spi= 0x0(0), conn_id= 0, keysize= 192, flags= 0x0
*Jan 20 16:48:27.703: IPSEC(crypto_ipsec_process_proposal):
transform proposal not supported for
identity:
{esp-aes 192 esp-md5-hmac }
*Jan 20 16:48:27.703: ISAKMP:(1030): IPSec policy invalidated proposal
*Jan 20 16:48:27.703: ISAKMP:(1030):Checking IPSec proposal 5
*Jan 20 16:48:27.703: ISAKMP: transform 1, ESP_AES
*Jan 20 16:48:27.703: ISAKMP: attributes in transform:
*Jan 20 16:48:27.703: ISAKMP: encaps is 1 (Tunnel)
*Jan 20 16:48:27.703: ISAKMP: SA life type in seconds
*Jan 20 16:48:27.703: ISAKMP: SA life duration (basic) of 28800
*Jan 20 16:48:27.703: ISAKMP: SA life type in kilobytes
*Jan 20 16:48:27.707: ISAKMP: SA life duration (VPI) of 0x0 0x46 0x50 0x0
*Jan 20 16:48:27.707: ISAKMP: authenticator is HMAC-SHA
*Jan 20 16:48:27.707: ISAKMP: key length is 128
*Jan 20 16:48:27.707: CryptoEngine0: validate proposal
*Jan 20 16:48:27.707: ISAKMP:(1030):atts are acceptable.
*Jan 20 16:48:27.707: IPSEC(validate_proposal_request): proposal part #1
*Jan 20 16:48:27.707: IPSEC(validate_proposal_request): proposal part #1,
(key eng. msg.) INBOUND local= 10.10.10.2, remote= 10.10.10.1,
local_proxy= 0.0.0.0/0.0.0.0/0/0 (type=4),
remote_proxy= 10.10.10.1/255.255.255.255/0/0 (type=1),
protocol= ESP, transform= esp-aes esp-sha-hmac (Tunnel),
lifedur= 0s and 0kb,
spi= 0x0(0), conn_id= 0, keysize= 128, flags= 0x0
*Jan 20 16:48:27.707: IPSEC(crypto_ipsec_process_proposal):
transform proposal not supported for
identity:
{esp-aes esp-sha-hmac }
*Jan 20 16:48:27.707: ISAKMP:(1030): IPSec policy invalidated proposal
*Jan 20 16:48:27.707: ISAKMP:(1030):Checking IPSec proposal 6
*Jan 20 16:48:27.707: ISAKMP: transform 1, ESP_AES
*Jan 20 16:48:27.707: ISAKMP: attributes in transform:
*Jan 20 16:48:27.707: ISAKMP: encaps is 1 (Tunnel)
*Jan 20 16:48:27.707: ISAKMP: SA life type in seconds
*Jan 20 16:48:27.707: ISAKMP: SA life duration (basic) of 28800
*Jan 20 16:48:27.707: ISAKMP: SA life type in kilobytes
*Jan 20 16:48:27.707: ISAKMP: SA life duration (VPI) of 0x0 0x46 0x50 0x0
*Jan 20 16:48:27.707: ISAKMP: authenticator is HMAC-MD5
*Jan 20 16:48:27.707: ISAKMP: key length is 128
*Jan 20 16:48:27.707: CryptoEngine0: validate proposal
*Jan 20 16:48:27.707: ISAKMP:(1030):atts are acceptable.
*Jan 20 16:48:27.707: IPSEC(validate_proposal_request): proposal part #1
*Jan 20 16:48:27.707: IPSEC(validate_proposal_request): proposal part #1,
(key eng. msg.) INBOUND local= 10.10.10.2, remote= 10.10.10.1,
local_proxy= 0.0.0.0/0.0.0.0/0/0 (type=4),
remote_proxy= 10.10.10.1/255.255.255.255/0/0 (type=1),
protocol= ESP, transform= esp-aes esp-md5-hmac (Tunnel),
lifedur= 0s and 0kb,
spi= 0x0(0), conn_id= 0, keysize= 128, flags= 0x0
*Jan 20 16:48:27.707: IPSEC(crypto_ipsec_process_proposal):
transform proposal not supported for
identity:
{esp-aes esp-md5-hmac }
*Jan 20 16:48:27.707: ISAKMP:(1030): IPSec policy invalidated proposal
*Jan 20 16:48:27.707: ISAKMP:(1030):Checking IPSec proposal 7
*Jan 20 16:48:27.707: ISAKMP: transform 1, ESP_3DES
*Jan 20 16:48:27.707: ISAKMP: attributes in transform:
*Jan 20 16:48:27.707: ISAKMP: encaps is 1 (Tunnel)
*Jan 20 16:48:27.707: ISAKMP: SA life type in seconds
*Jan 20 16:48:27.707: ISAKMP: SA life duration (basic) of 28800
*Jan 20 16:48:27.707: ISAKMP: SA life type in kilobytes
*Jan 20 16:48:27.707: ISAKMP: SA life duration (VPI) of 0x0 0x46 0x50 0x0
*Jan 20 16:48:27.707: ISAKMP: authenticator is HMAC-SHA
*Jan 20 16:48:27.711: CryptoEngine0: validate proposal
*Jan 20 16:48:27.711: ISAKMP:(1030):atts are acceptable.
*Jan 20 16:48:27.711: IPSEC(validate_proposal_request): proposal part #1
*Jan 20 16:48:27.711: IPSEC(validate_proposal_request): proposal part #1,
(key eng. msg.) INBOUND local= 10.10.10.2, remote= 10.10.10.1,
local_proxy= 0.0.0.0/0.0.0.0/0/0 (type=4),
remote_proxy= 10.10.10.1/255.255.255.255/0/0 (type=1),
protocol= ESP, transform= esp-3des esp-sha-hmac (Tunnel),
lifedur= 0s and 0kb,
spi= 0x0(0), conn_id= 0, keysize= 0, flags= 0x0
*Jan 20 16:48:27.711: IPSEC(crypto_ipsec_process_proposal):
transform proposal not supported for
identity:
{esp-3des esp-sha-hmac }
*Jan 20 16:48:27.711: ISAKMP:(1030): IPSec policy invalidated proposal
*Jan 20 16:48:27.711: ISAKMP:(1030):Checking IPSec proposal 8
*Jan 20 16:48:27.711: ISAKMP: transform 1, ESP_3DES
*Jan 20 16:48:27.711: ISAKMP: attributes in transform:
*Jan 20 16:48:27.711: ISAKMP: encaps is 1 (Tunnel)
*Jan 20 16:48:27.711: ISAKMP: SA life type in seconds
*Jan 20 16:48:27.711: ISAKMP: SA life duration (basic) of 28800
*Jan 20 16:48:27.711: ISAKMP: SA life type in kilobytes
*Jan 20 16:48:27.711: ISAKMP: SA life duration (VPI) of 0x0 0x46 0x50 0x0
*Jan 20 16:48:27.711: ISAKMP: authenticator is HMAC-MD5
*Jan 20 16:48:27.711: CryptoEngine0: validate proposal
*Jan 20 16:48:27.711: ISAKMP:(1030):atts are acceptable.
*Jan 20 16:48:27.711: IPSEC(validate_proposal_request): proposal part #1
*Jan 20 16:48:27.711: IPSEC(validate_proposal_request): proposal part #1,
(key eng. msg.) INBOUND local= 10.10.10.2, remote= 10.10.10.1,
local_proxy= 0.0.0.0/0.0.0.0/0/0 (type=4),
remote_proxy= 10.10.10.1/255.255.255.255/0/0 (type=1),
protocol= ESP, transform= esp-3des esp-md5-hmac (Tunnel),
lifedur= 0s and 0kb,
spi= 0x0(0), conn_id= 0, keysize= 0, flags= 0x0
*Jan 20 16:48:27.715: IPSEC(crypto_ipsec_process_proposal):
transform proposal not supported for
identity:
{esp-3des esp-md5-hmac }
*Jan 20 16:48:27.715: ISAKMP:(1030): IPSec policy invalidated proposal
*Jan 20 16:48:27.715: ISAKMP:(1030):Checking IPSec proposal 9
*Jan 20 16:48:27.715: ISAKMP: transform 1, ESP_DES
*Jan 20 16:48:27.715: ISAKMP: attributes in transform:
*Jan 20 16:48:27.715: ISAKMP: encaps is 1 (Tunnel)
*Jan 20 16:48:27.715: ISAKMP: SA life type in seconds
*Jan 20 16:48:27.715: ISAKMP: SA life duration (basic) of 28800
*Jan 20 16:48:27.715: ISAKMP: SA life type in kilobytes
*Jan 20 16:48:27.715: ISAKMP: SA life duration (VPI) of 0x0 0x46 0x50 0x0
*Jan 20 16:48:27.715: ISAKMP: authenticator is HMAC-MD5
*Jan 20 16:48:27.715: CryptoEngine0: validate proposal
*Jan 20 16:48:27.715: ISAKMP:(1030):atts are acceptable.
*Jan 20 16:48:27.715: IPSEC(validate_proposal_request): proposal part #1
*Jan 20 16:48:27.715: IPSEC(validate_proposal_request): proposal part #1,
(key eng. msg.) INBOUND local= 10.10.10.2, remote= 10.10.10.1,
local_proxy= 0.0.0.0/0.0.0.0/0/0 (type=4),
remote_proxy= 10.10.10.1/255.255.255.255/0/0 (type=1),
protocol= ESP, transform= esp-des esp-md5-hmac (Tunnel),
lifedur= 0s and 0kb,
spi= 0x0(0), conn_id= 0, keysize= 0, flags= 0x0
*Jan 20 16:48:27.715: ISAKMP:(1030): processing NONCE payload.
message ID = 1887305923
*Jan 20 16:48:27.715: ISAKMP:(1030): processing ID payload.
message ID = 1887305923
*Jan 20 16:48:27.715: ISAKMP:(1030): processing ID payload.
message ID = 1887305923
*Jan 20 16:48:27.715: ISAKMP:(1030): asking for 1 spis from ipsec
*Jan 20 16:48:27.715: ISAKMP:(1030):Node 1887305923,
Input = IKE_MESG_FROM_PEER, IKE_QM_EXCH
*Jan 20 16:48:27.715: ISAKMP:(1030):Old State = IKE_QM_READY
New State = IKE_QM_SPI_STARVE
*Jan 20 16:48:27.719: IPSEC(key_engine): got a queue event with 1 KMI message(s)
*Jan 20 16:48:27.719: IPSEC(spi_response): getting spi 185206738 for SA
from 10.10.10.2 to 10.10.10.1 for prot 3
*Jan 20 16:48:27.719: crypto_engine: Generate IKE hash
*Jan 20 16:48:27.719: crypto_engine: Generate IKE QM keys
*Jan 20 16:48:27.719: crypto_engine: Create IPSec SA (by keys)
*Jan 20 16:48:27.719: crypto_engine: Generate IKE QM keys
*Jan 20 16:48:27.719: crypto_engine: Create IPSec SA (by keys)
*Jan 20 16:48:27.719: ISAKMP:(1030): Creating IPSec SAs
*Jan 20 16:48:27.719: inbound SA
from 10.10.10.1 to 10.10.10.2 (f/i) 0/ 0
(proxy 10.10.10.1 to 0.0.0.0)
*Jan 20 16:48:27.719: has spi 0xB0A07D2 and conn_id 0
*Jan 20 16:48:27.719: lifetime of 28800 seconds
*Jan 20 16:48:27.719: lifetime of 4608000 kilobytes
*Jan 20 16:48:27.719: outbound SA
from 10.10.10.2 to 10.10.10.1 (f/i) 0/0 (proxy 0.0.0.0 to 10.10.10.1)
*Jan 20 16:48:27.719: has spi 0xB22446D and conn_id 0
*Jan 20 16:48:27.719: lifetime of 28800 seconds
*Jan 20 16:48:27.719: lifetime of 4608000 kilobytes
*Jan 20 16:48:27.719: crypto_engine: Encrypt IKE packet
*Jan 20 16:48:27.719: ISAKMP:(1030): sending packet to 10.10.10.1
my_port 500 peer_port 500 (R)
QM_IDLE
*Jan 20 16:48:27.719: ISAKMP:(1030):Node 1887305923,
Input = IKE_MESG_FROM_IPSEC, IKE_SPI_REPLY
*Jan 20 16:48:27.719: ISAKMP:(1030):Old State = IKE_QM_SPI_STARVE
New State = IKE_QM_R_QM2
*Jan 20 16:48:27.719: IPSEC(key_engine): got a queue event with 1 KMI message(s)
*Jan 20 16:48:27.723: IPSec: Flow_switching Allocated flow for sibling 80000014
*Jan 20 16:48:27.723: IPSEC(policy_db_add_ident): src 0.0.0.0,
dest 10.10.10.1, dest_port 0
*Jan 20 16:48:27.723: IPSEC(create_sa): sa created,
(sa) sa_dest= 10.10.10.2, sa_proto= 50,
sa_spi= 0xB0A07D2(185206738),
sa_trans= esp-des esp-md5-hmac , sa_conn_id= 37
*Jan 20 16:48:27.723: IPSEC(create_sa): sa created,
(sa) sa_dest= 10.10.10.1, sa_proto= 50,
sa_spi= 0xB22446D(186795117),
sa_trans= esp-des esp-md5-hmac , sa_conn_id= 38
!--- The two IPSec SAs shown above are for management purposes.
*Jan 20 16:48:27.771: ISAKMP (0:1030): received packet from 10.10.10.1 dport
500 sport 500 Global (R)
QM_IDLE
*Jan 20 16:48:27.771: crypto_engine: Decrypt IKE packet
*Jan 20 16:48:27.771: crypto_engine: Generate IKE hash
*Jan 20 16:48:27.771: ISAKMP:(1030):deleting node 1887305923
error FALSE reason "QM done (await)"
*Jan 20 16:48:27.771: ISAKMP:(1030):Node 1887305923,
Input = IKE_MESG_FROM_PEER, IKE_QM_EXCH
*Jan 20 16:48:27.771: ISAKMP:(1030):Old State = IKE_QM_R_QM2
New State = IKE_QM_PHASE2_COMPLETE
*Jan 20 16:48:27.771: IPSEC(key_engine): got a queue event
with 1 KMI message(s)
*Jan 20 16:48:27.771: IPSEC(key_engine_enable_outbound):
rec'd enable notify from ISAKMP
*Jan 20 16:48:27.771: IPSEC(key_engine_enable_outbound):
enable SA with spi 186795117/50
*Jan 20 16:48:27.771: IPSEC(update_current_outbound_sa):
updated peer 10.10.10.1 current outbound sa
to SPI B22446D
*Jan 20 16:48:27.771: ISAKMP (0:1030): received packet from
10.10.10.1 dport 500 sport 500 Global (R)
QM_IDLE
*Jan 20 16:48:27.771: ISAKMP: set new node -1259355083 to QM_IDLE
*Jan 20 16:48:27.771: crypto_engine: Decrypt IKE packet
*Jan 20 16:48:27.775: crypto_engine: Generate IKE hash
*Jan 20 16:48:27.775: ISAKMP:(1030): processing HASH payload.
message ID = -1259355083
*Jan 20 16:48:27.775: ISAKMP:(1030): processing SA payload.
message ID = -1259355083
*Jan 20 16:48:27.775: ISAKMP:(1030):Checking IPSec proposal 1
*Jan 20 16:48:27.775: ISAKMP: transform 1, ESP_AES
*Jan 20 16:48:27.775: ISAKMP: attributes in transform:
*Jan 20 16:48:27.775: ISAKMP: encaps is 1 (Tunnel)
*Jan 20 16:48:27.775: ISAKMP: SA life type in seconds
*Jan 20 16:48:27.775: ISAKMP: SA life duration (basic) of 28800
*Jan 20 16:48:27.775: ISAKMP: SA life type in kilobytes
*Jan 20 16:48:27.775: ISAKMP: SA life duration (VPI) of 0x0 0x46 0x50 0x0
*Jan 20 16:48:27.775: ISAKMP: authenticator is HMAC-SHA
*Jan 20 16:48:27.775: ISAKMP: key length is 256
*Jan 20 16:48:27.775: CryptoEngine0: validate proposal
*Jan 20 16:48:27.775: ISAKMP:(1030):atts are acceptable.
*Jan 20 16:48:27.775: IPSEC(validate_proposal_request): proposal part #1
*Jan 20 16:48:27.775: IPSEC(validate_proposal_request): proposal part #1,
(key eng. msg.) INBOUND local= 10.10.10.2, remote= 10.10.10.1,
local_proxy= 0.0.0.0/0.0.0.0/0/0 (type=4),
remote_proxy= 172.16.1.0/255.255.255.0/0/0 (type=4),
protocol= ESP, transform= esp-aes 256 esp-sha-hmac (Tunnel),
lifedur= 0s and 0kb,
spi= 0x0(0), conn_id= 0, keysize= 256, flags= 0x0
*Jan 20 16:48:27.775: IPSEC(crypto_ipsec_process_proposal):
transform proposal not supported for
identity:
{esp-aes 256 esp-sha-hmac }
*Jan 20 16:48:27.775: ISAKMP:(1030): IPSec policy invalidated proposal
*Jan 20 16:48:27.775: ISAKMP:(1030):Checking IPSec proposal 2
*Jan 20 16:48:27.775: ISAKMP: transform 1, ESP_AES
*Jan 20 16:48:27.775: ISAKMP: attributes in transform:
*Jan 20 16:48:27.775: ISAKMP: encaps is 1 (Tunnel)
*Jan 20 16:48:27.775: ISAKMP: SA life type in seconds
*Jan 20 16:48:27.775: ISAKMP: SA life duration (basic) of 28800
*Jan 20 16:48:27.775: ISAKMP: SA life type in kilobytes
*Jan 20 16:48:27.775: ISAKMP: SA life duration (VPI) of 0x0 0x46 0x50 0x0
*Jan 20 16:48:27.775: ISAKMP: authenticator is HMAC-MD5
*Jan 20 16:48:27.775: ISAKMP: key length is 256
*Jan 20 16:48:27.775: CryptoEngine0: validate proposal
*Jan 20 16:48:27.775: ISAKMP:(1030):atts are acceptable.
*Jan 20 16:48:27.775: IPSEC(validate_proposal_request): proposal part #1
*Jan 20 16:48:27.799: IPSEC(create_sa): sa created,
(sa) sa_dest= 10.10.10.2, sa_proto= 50,
sa_spi= 0x990A0C2C(2567572524),
sa_trans= esp-des esp-md5-hmac , sa_conn_id= 39
*Jan 20 16:48:27.799: IPSEC(create_sa): sa created,
(sa) sa_dest= 10.10.10.1, sa_proto= 50,
sa_spi= 0x9FBC4C0D(2679917581),
sa_trans= esp-des esp-md5-hmac , sa_conn_id= 40
!--- The two IPSec SAs shown above are for actual data traffic.